Bulletin: We are aware of the fraudlent offers for our Raminator Monster Truck. Be advised that the only place to purchase the Raminator is here on Primal RC or from our authorized dealers.
Taylor RC 50GT Raminator High Performance Engine/Pipe Kit with Billet Head!
Taylor RC 50GT Raminator High Performance Engine/Pipe Kit with Billet Head!

Taylor RC 50GT Raminator High Performance Engine/Pipe Kit with Billet Head!

SKU: TRC50GT
Your Price: $2,195.55
Retail Price:$2,299.94
You Save:$104.39(5%)
Taylor RC 50GT Raminator Engine/Pipe Kit
Part Number: TRC50GT
Availability: In Stock

Taylor RC (formerly RCMax) Complete Ready to Install High Performance Engine and Pipe package for the PRIMAL RC RAMINATOR Monster Truck!

This engine will provide you with over 3 times the power of stock Raminator engine but not quite the gear shattering torque of the 80 SUPREME for those concerned about drivetrain reliability.

The package includes the following:

  • 50cc Billet Reed engine (40mm Bore x 39.6mm Stroke)
  • Taylor RC GT CYLINDER (Insane torque output with staged triple exhaust port)
  • Billet cylinder head (more torque over cast head)
  • 78mm 3-Shoe GO-PED CLUTCH SYSTEM
  • Fits straight onto the stock Ram Clutch bell housing and transmission for easy swap.
  • NEW 2020 Oppama Japanese Ignition System
  • Taylor RC BILLET HD PULL STARTER
  • Taylor RC Reed System with 8 custom high tension carbon-fiber petals.
  • Walbro WJ71 Carb
  • RAM AIR Dual layer foam filter
  • Taylor RC BIG BORE RAMINATOR EXHAUST and fitting kit.
  • Custom Throttle cable linkage bracket
  • Custom Billet RH and LH engine brackets to replace stock engine brackets.
  • Custom Tubular Steel exhaust protection rollover bar with twin Taylor RC flags for show!
  • The famous Taylor RC Official Hat

THE 50 FITS ALMOST THE SAME AS OUR 80cc MONSTER, JUST WITHOUT THE NEED TO CHANGE TRANNY, SEE INSTALL VIDEO BELOW.

Fitment into the primal Raminator is fairly straightforward. Once you have removed the stock engine and pipe, also remove the center top cross over link bar between the two side chassis plates.

While the stock engine is out, we highly recommend cutting out a section of the side chassis plate next to the pull starter so that you can fit the engine (or even the stock engine) Without having to remove the pull starter or remove the side chassis plate itself. (see photo above with section cut out around the pull starter).

Then the engine itself can drop in and bolt up with the supplied engine brackets (fitment shown in pics).

As mentioned above, if you cut your chassis it will drop in, if not, remove the pull start side chassis plate and then there is room to fit. Fit all the engine mounting bolts supplied. Next you can hook up the throttle linkage cable onto the big bore WJ71 carb. Simply remove the linkage cable hole from the stock carb by popping the bracket off and removing the E clip. Then put this piece onto the Hole cut out in the WJ71 Carb arm as shown in photos.

Finally you can fit the cable to the supplied holder bracket and adjust to suit. (again see photos) The last step is to fit the exhaust mounting bracket to the car ready to support the pipe. (the main belly section of the pipe fits to the car AFTER the body has been fitted - slide in through the gap at back of the roll over bar and into place). Then its as simple as two retaining springs and the one nut on the rubber mount!

INSTALL VIDEO

Related Items

Taylor RC SUPREME 55 Dragster Engine/Titanium Pipe Kit for Primal RC Dragster
TRCS55
$2,305.58
In Stock
Add To Cart
Taylor RC SUPREME 71cc Dragster Engine/Titanium Pipe Kit for Primal RC Dragster
TRCS71
$2,599.98
In Stock
Add To Cart
Taylor RC 80SUPREME Raminator Engine/Pipe Kit with Taylor RC 110mm Clutch, Complete Kit
TRC80SUPREME
$3,409.95
In Stock
Add To Cart
Monster Truck Billet Beadlock Set (silver) (set of 4) - Taylor RC
TRC09002
$164.98
In Stock
Add To Cart
Monster Truck Upgraded Steering Link Mounts - Taylor RC
TRC019
$82.48
In Stock
Add To Cart

Recently Viewed Items